Custom Meta Tags - Dynamic

Hero Banner

New Product Introduction

NPI Body

STMicroelectronics STLINK-V3PWR

STLINK-V3 compact in-circuit debugger and programmer for STM32

STLINK-V3PWR is a two-in-one standalone debugger probe and a source measurement unit (SMU) designed to synchronize code execution with a power consumption of STM32 applications in real time. It is specifically adapted for power consumption optimization.

It can be used as a standalone source measurement unit to supply power and measure the current consumption of the target application. The product keeps the output voltage constant during fast current transient .

STLINK-V3PWR is also a standalone debugging and programming probe for STM32 microcontrollers. The product embeds a multi-path bridge interface with an integrated level shifter.

Key features

1 Quadrant source measurement unit
Auxiliary output voltage source from 1.6 to 3.6 V under up to 2 A
Debugging of embedded applications
Four bi-color LEDs providing probe state

Additional features

1‑Quadrant source measurement unit with high resolution, and measurement flexibility:
- Programmable voltage source from 1.6 to 3.6 V
- Output current rating 500 mA with over-current protection (OCP) at 550 mA
- Programmable sampling rate from 1 SPS to 100 kSPS
- Dynamic measurement:100 nA to 550 mA current / 160 nW to 1.65 W power measurements50 kHz bandwidth / 1.6 MHz acquisition / 2% accuracyCompatible with EEMBC^® ULPMark™ tests
Auxiliary output voltage source from 1.6 to 3.6 V under up to 2 A (no current measurement, OCP at 2.5 A)
Debugging of embedded applications:
- JTAG / Serial Wire Debug (SWD):SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 10 MHzJTAG communication support up to 20 MHz
- UART interface on Virtual COM port (VCP) with frequency up to 12 MHz
- Multi-path bridge USB to SPI/I2C/CAN/GPIOs
- Integrated level shifter I/O voltage 1.6 to 3.6V adaptable
Four bi-color LEDs providing probe state
Three STDC14 to MIPI10 / STDC14 / MIPI20 flat cables with 1.27 mm pitch connectors
Four cables (two male/male and two male/female)
USB Type-C^® connector:
- Powered through USB Type-C^® (5 V/3 A maximum)
- USB 2.0 high‑speed interface
- Probe firmware update through USB
Direct support from STM32CubeMonitor-Power software tool

Applications

Tool is specifically adapted for power consumption optimization

Available tools

STSW-LINK007 : ST-LINK, ST-LINK/V2, ST-LINK/V2-1, STLINK-V3 boards firmware upgrade

STM32CubeMonitor-Power:

Graphical tool displaying on PC power data coming from STLink-V3PWR

STM32CubeMonitor-Power (STM32CubeMonPwr) enables developers to swiftly analyze the power/low‑power consumption of target boards, and optimize the energy efficiency of their applications. This software tool acquires power measurements through the STLINK-V3PWR probe, the X-NUCLEO-LPM01A expansion board, or the energy meter of the STM32L562E-DK Discovery kit specialized intermediate board, and displays these measurements using an intuitive graphical interface.

DATASHEET

STLINK-V3SET:

STLINK-V3 modular in-circuit debugger and programmer for STM32/STM8

The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board. The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

DATASHEET

STLINK-V3MINIE:

STLINK-V3 compact in-circuit debugger and programmer for STM32

STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for STM32 microcontrollers. The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.

DATASHEET

STLINK-V3MODS:

STLINK v3 compact in-circuit debugger and programmer for STM32

The STLINK-V3MODS is a small size debugging and programming probe for STM32 microcontrollers. The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.

DATASHEET

B-STLINK-VOLT:

Voltage adaptation board for STLINK-V3SET

The B-STLINK-VOLT board is an additional module for the STLINK-V3SET, performing voltage adaptation for STM32 microcontroller targets running below 3.3 V down to 1.65 V. This module can be enclosed directly in the original STLINK-V3SET casing when used as an STM32 debugging probe (JTAG/SWD/SWV/VCP) through the STDC14 connector. It can be inserted also between the STLINK-V3SET main board (MB1441) and its baseline adapter board (MB1440) when providing access to bridge signals and other connectors.

DATASHEET

B-STLINK-ISOL:

Isolation and voltage adapter board for STLINK-V3SET

The B-STLINK-ISOL board is an additional module for STLINK-V3SET, performing galvanic isolation and voltage adaptation for STM32 microcontroller targets running below 3.3 V down to 1.65 V. The module can be enclosed directly in the original STLINK-V3SET casing, when used as an STM32 debugging probe (JTAG/SWD/SWV/VCP) through the STDC14 connector. It can be also inserted between the STLINK-V3SET main board (MB1441) and its adapter board (MB1440) when providing access to bridge signals and other connectors.

DATASHEET